Igneous Extruder


Igneous extruder

Minecraft physics are fun!

An igneous extruder, or extruder for short, is a machine that mixes hot and cold fluids to create items.

Obtaining

A placed igneous extruder can be instantly picked up by dismantling it with a wrench. Its configuration is preserved in the item. It can also be mined using a pickaxe, though this can be much slower.

Crafting

Upgrading

An igneous extruder is initially at the lowest tier (basic). It can be upgraded to higher tiers using upgrade kits and conversion kits.

Usage

Placement

When placed, an igneous extruder faces the player. It can face any of the four cardinal directions, and can be rotated using a wrench.

Processing

An igneous extruder can be configured to mix a certain pair of fluids into a certain item following one of its available recipes.

When an igneous extruder’s input tanks are filled with at least 1,000 mB of the fluids corresponding to the configured recipe, the machine will start consuming Redstone Flux to produce the recipe’s output item. Every produced item requires certain amounts of energy and the two fluids. When enough energy has been consumed for an item, the input is consumed and the output is placed in the output slot.

The speed at which an igneous extruder produces items depends on how much energy it can use per tick. This in turn depends on how much power is being supplied, and on the machine’s maximum power usage. A basic extruder has a maximum power usage of 20 RF/t. This can be increased by upgrading the machine to a higher tier, and by installing certain augments.

Input and output

Fluids and items can enter and exit an igneous extruder through its sides. Every side of an extruder may correspond to its input tanks, its output slot, or both at the same time.

An igneous extruder can automatically transfer items out of any sides that directly correspond to its output slot. This is called auto-output, and occurs whenever the machine finishes processing an item, or every 32 ticks (1.6 seconds) if the machine is inactive.

A basic igneous extruder can automatically output up to 16 items at a time. This amount can be increased by upgrading the machine to a higher tier.

Which sides correspond to which tanks/slots and whether auto-output is enabled can be configured using the Configuration tab in the machine’s GUI.

Redstone control

An igneous extruder may be configured to respond to redstone signals. It can be in one of three modes:

Ignored
Redstone control is disabled. The extruder works whenever possible. This is the default mode.
Low
The extruder works when not powered. When powered, it stops working.
High
The extruder only works when powered.

The current mode can be set using the Redstone Control tab in the machine’s GUI.

Security

An igneous extruder can have a signalum security lock installed to restrict who can access it.

Redprints

An igneous extruder’s configuration can be saved on a redprint to be copied to other extruders.

Light source

When an igneous extruder is active, it emits a light level of 14.

Tiers

Igneous extruders come in five tiers.

Tier Max. power usage Augment slots Max. items per auto-transfer
Basic 20 RF/t 0 16
Hardened 30 RF/t 1 16
Reinforced 40 RF/t 2 28
Signalum 50 RF/t 3 44
Resonant 60 RF/t 4 64

Augmentation

An igneous extruder can have augments installed to improve certain properties or to change how it works. The amount of augments that can be installed depends on the machine’s tier. A basic extruder cannot be augmented.

Augments can be installed in the Augmentation tab in an extruder’s GUI.

Augment Installable in Description
Auxiliary Reception Coil Auxiliary Reception Coil Any machine Increases a machine's maximum power usage (speed). However, also increases the amount of energy required per operation. Can be installed multiple times.
Pyroclastic Injection Pyroclastic Injection Igneous Extruder A specialization that allows for an igneous extruder to work without cold fluids (water), so that only hot fluids (lava) are required.
Clastic Deposition Clastic Deposition Igneous Extruder A specialization that allows for an igneous extruder to produce sedimentary rock, such as sand or gravel. However, an igneous extruder can only produce sedimentary rock when installed.

Recipes

When a fluid’s input amount is listed as 0 mB, it is not consumed; it only needs to be inside the corresponding input tank.

Result(s) Ingredients Energy Igneous Extruder recipe
Cobblestone
Lava (0 mB) +
Water (0 mB)
400 RF
Stone
Lava (0 mB) +
Water (1000 mB)
800 RF
Obsidian
Lava (1000 mB) +
Water (1000 mB)
1600 RF
Granite
Lava (0 mB) +
Water (1000 mB)
800 RF
Diorite
Lava (0 mB) +
Water (1000 mB)
800 RF
Andesite
Lava (0 mB) +
Water (1000 mB)
800 RF
Thermal Expansion 5
Machines
Redstone Furnace
Pulverizer
Sawmill
Induction Smelter
Phytogenic Insolator
Compactor
Magma Crucible
Fractionating Still
Fluid Transposer
Energetic Infuser
Centrifugal Separator
Sequential Fabricator
Alchemical Imbuer
Arcane Ensorcellator
Glacial Precipitator
Igneous Extruder
Devices
Aqueous Accumulator
Nullifier
Thermal Mediator
Arboreal Extractor
Aquatic Entangler
Item Allocator
Fluid Allocator
Lexical Transmuter
Insightful Condenser
Decoctive Diffuser
Factorizer
Creature Encaptulator
Vacuumulator
Dynamos
Steam Dynamo
Magmatic Dynamo
Compression Dynamo
Reactant Dynamo
Enervation Dynamo
Numismatic Dynamo
Storage
Energy Cell
Flux Capacitor
Portable Tank
Reservoir
Cache
Strongbox
Satchel
Augments
Machine
Auxiliary Reception Coil
Auxiliary Sieve
Nullification Chamber
Trivection Chamber
Flux Anodizers
Pyrolytic Conversion
Tectonic Initiator
Resin Funnel
Metallurgical Recovery
Pyro-Concentrator
Nutrient Recovery
Sapling Infuser
Monoculture Cycle
Numismatic Press
Gearworking Die
Pyroconvective Loop
Reflux Column
Alchemical Retort
Flux Linkage Concentrator
Flux Reconstruction
Parabolic Flux Coupling
Enstabulation Apparatus
Pattern Validation
Fluidic Fabrication
Reagent Recovery
Pyroclastic Injection
Clastic Deposition
Dynamo
Auxiliary Transmission Coil
Fuel Catalyzer
Transmission Coil Ducting
Excitation Field Limiter
Boiler Conversion
Turbine Conversion
Isentropic Reservoir
Closed-Loop Cooling
Ignition Plugs
Agitative Manifold
Elemental Catalyzer
Disjunctive Extraction
Lapidary Calibration
Other
Coolants
Florb
(
Magmatic
)
Morb
(
Reusable
)

© Copyright 2015-2018 Team CoFH. Powered by GitHub Pages, Jekyll, UIkit.
Last updated: 2018-06-17 14:00:02 +0000